• View Cart
    Add to basket / Details

    10m Cable Extension

    €733.95 Excl. VAT     (€880.74 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    10m SWA power and signal cable extension used for tube tower installations to pass through the foundation up to the controller.
  • View Cart
    Add to basket / Details

    11kW Generator

    €2,050.18 Excl. VAT     (€2,460.22 Inc. VAT)
    • Replacement generator for G-11 and Gaia-Wind G133 wind turbines.
    • 400/415V, 3PH, 50/60Hz.
    • Supplied with flange, temperature sensor & cable glands fitted.
    Vibration mounts sold separately.
  • View Cart
    Add to basket / Details

    24V DC Power Supply

    €82.72 Excl. VAT     (€99.26 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine fitted with a three phase controller.
  • View Cart
    Add to basket / Details

    ANEMOMETER

    €151.45 Excl. VAT     (€181.74 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbines.
    The anemometer will measure the wind speed accurately to ensure the proper operation of the turbine. The service life of the part is approximately 5 years but can fail within that time due to a number of reasons for example ice build up and bird attacks are the two most common reasons for early failure.
    • Supplied with cable.
  • View Cart
    Add to basket / Details

    Bird Guards

    €81.55 Excl. VAT     (€97.86 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    Two specially shaped plastic guards that fit over the open areas on the underside of the turbine nacelle. Prevents birds entering the nacelle and trigging errors.
    • Includes all fixings.
  • View Cart
    Add to basket / Details

    Blade Repair – Gelcoat Filler

    €34.95 Excl. VAT     (€41.94 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines.
    Used to repair minor cracks and holes on the blade, i.e. bump-stop damage.
  • View Cart
    Add to basket / Details

    Blade Spring Brackets (Pair)

    €221.35 Excl. VAT     (€265.62 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines.
    Set includes:
    • 2 x brackets
    • 4 x M10 x 40mm hex bolts
    • 4 x M10 washers
  • View Cart
    Add to basket / Details

    Blade Spring Kit

    €361.15 Excl. VAT     (€433.38 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine.
    We would recommend that when a spring becomes damaged or broken it is necessary to replace the full set rather than just one spring. The loss of a single spring will increase the loads on the remaining springs and could accelerate fatigue.The parts included in this kit:
    • 4 x Blade springs
    • 6 x R-clips
    • 8 x Nylon bushes
    • 1 x M20 machined rod
    • 4 x M20 nuts
    • 2 x M20 washers
    • 1 x Blade retaining strap
    • 2 x M8 screws
  • View Cart
    Add to basket / Details

    Brake Actuator

    €233.00 Excl. VAT     (€279.60 Inc. VAT)
  • View Cart
    Add to basket / Details

    Brake Arm

    €302.90 Excl. VAT     (€363.48 Inc. VAT)
  • View Cart
    Add to basket / Details

    Brake Caliper

    €349.50 Excl. VAT     (€419.40 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines.
    • Includes 2 brake pads.
  • View Cart
    Add to basket / Details

    Brake on / off Sensor

    €38.45 Excl. VAT     (€46.14 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • Supplied with cable.
  • View Cart
    Add to basket / Details

    Brake Pads

    €104.85 Excl. VAT     (€125.82 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    The brake pads require a manual adjustment to ensure proper functionality. Please note the brake pads are a serviceable part and will require replacement according to the service manual.The replacement should only be carried out by a competent and Ryse Energy trained technician.
  • View Cart
    Add to basket / Details

    Brake Pads Worn Sensor

    €34.95 Excl. VAT     (€41.94 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    Replacement brake pads worn sensor, supplied with gland.
  • View Cart
    Add to basket / Details

    Brake Relay 24V DC

    €20.97 Excl. VAT     (€25.16 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
  • View Cart
    Add to basket / Details

    Brake Relay 250V AC

    €34.95 Excl. VAT     (€41.94 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine fitted with a three phase controller.
    • 250V AC contact rating.
  • View Cart
    Add to basket / Details

    Bump Stop Kit

    €161.94 Excl. VAT     (€194.33 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine.
    The rubber bump-stops are used to protect the back of the blade whilst teetering, as with all rubber product this will degrade over time due to exposure to oxygen and UV light as well as wearing through repeated blade contact.The bump-stops should last for 24 months before requiring replacement but on site with high instances of teeter movement in the blade such as high turbulent site then wear will be accelerated.The parts included in this kit:
    • 2 x bump-stops
    • 2 x M16 screws and washers
    • Metal spacers behind should be re-used.
  • View Cart
    Add to basket / Details

    Cable Twist Sensor Assembly

    €304.07 Excl. VAT     (€364.88 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    A tower mounted sensor which detects if the nacelle down cables have become excessively twisted.
  • View Cart
    Add to basket / Details

    Capacitor 10 kvar

    €291.25 Excl. VAT     (€349.50 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines fitted with a three phase controller.
  • View Cart
    Add to basket / Details

    Capacitor Contactor 230V AC Coil 50/60Hz

    €92.04 Excl. VAT     (€110.45 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine fitted with a IC1100 three phase controller.
    • Please check compatibility. Older IC1000 controllers require low voltage 24v AC coil version.
    • Image shown may differ from the unit fitted. Image shown is the latest version of the contactor with upgraded coiled jumpers.
  • View Cart
    Add to basket / Details

    Capacitor Contactor 24V AC Coil 50/60Hz

    €151.45 Excl. VAT     (€181.74 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine fitted with an older IC1000 three phase controller.
    • Please check compatibility. Newer IC1100 controllers require 230v AC coil version.
    • Image shown may differ from the unit fitted. Image shown is the latest version of the contactor with upgraded coiled jumpers.
  • View Cart
    Add to basket / Details

    Contactor 24V DC Coil

    €326.20 Excl. VAT     (€391.44 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
    • Replacement for contactor K17.1 and K17.3.
  • View Cart
    Add to basket / Details

    Controller Cabinet Key

    €11.65 Excl. VAT     (€13.98 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • Replacement cabinet key used to open the controller door both three phase and single phase versions.
  • View Cart
    Add to basket / Details

    Controller Door Hingepins

    €30.29 Excl. VAT     (€36.35 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • Set of 2.
    Replacement hinge pin for the controller door of the three phase controller cabinet.
  • View Cart
    Add to basket / Details

    Controller Door Lock

    €17.48 Excl. VAT     (€20.98 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
  • View Cart
    Add to basket / Details

    Flexible Coupling

    €384.45 Excl. VAT     (€461.34 Inc. VAT)
    • The high speed coupling is the part situated between the gearbox and generator. On high turbulence sites or on installations with increased start stops this coupling may wear prematurely requiring replacement.
    • Supplied with 8 fasteners.
  • View Cart
    Add to basket / Details

    Frame Bracing Kit

    €209.70 Excl. VAT     (€251.64 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine
    Retrofit frame bracing kit. Once purchased, a copy of the fitting procedure P9000004 will be emailed.It is advised the holes are marked and drilled using the Drilling Template available below.
  • View Cart
    Add to basket / Details

    Gearbox Oil

    €163.10 Excl. VAT     (€195.72 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbine.
    • Poor oil quality is one of the primary causes of gearbox failure.
    • The gearbox oil should be changed every 30,000 hours. This should align roughly with every 3rd service.
    • 11L of oil supplied in plastic container with sealed tamper proof lid. This is sufficient for one oil change on a turbine.
  • View Cart
    Add to basket / Details

    Gearbox Seal

    €16.31 Excl. VAT     (€19.57 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbines.
    A gearbox seal is a rubber seal for the gearbox low speed shaft at the rear, it is used in instances where oil is leaking from the gearbox.
  • View Cart
    Add to basket / Details

    Generator Power Cable Plug

    €18.64 Excl. VAT     (€22.37 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    Replacement for the cable end plug from generator to controller.
  • View Cart
    Add to basket / Details

    Generator to Controller Power Cable (23m)

    €198.05 Excl. VAT     (€237.66 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbines on 15m and 18m towers.
    • Supplied with industrial plug on the controller end. Correctly sized ring crimps for connection to the generator on the other.
  • View Cart
    Add to basket / Details

    Generator to Controller Power Cable (33m)

    €279.60 Excl. VAT     (€335.52 Inc. VAT)
    • Suitable for the G-11 and G133 wind turbines on 23m and 27m towers.
    • Supplied with industrial plug on the controller end. Correctly sized ring crimps for connection to the generator on the other.
    • Modified cable support bracket
    • Flexible cable support
    The 33m power cable is ordered as a special with a lead time of up to 4 weeks.
  • View Cart
    Add to basket / Details

    High Speed / Low Speed Proximity Sensor

    €46.60 Excl. VAT     (€55.92 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    There are two identical sensors fitted on he G-11 and Gaia-Wind G133 wind turbine. 1 is located in the back cover of the generator and the other is located at the end of the low speed shaft.
  • View Cart
    Add to basket / Details

    Hub Bushing Kit

    €588.33 Excl. VAT     (€706.00 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    If installed correctly and when operating in normal conditions for a Class III turbine the hub bushings have an expected service life of 24 months however high turbulence at sites will decrease the life of the hub bushings. Therefore the bushings should be inspected at least annually in accordance with manufacturers service manual and bulletins.The parts included in this kit:
      • 2 x Hub bushes
      • 1 x M20 machined rod
      • 4 x M20 nuts
      • 1 x M20 DTI washer
      • 2 x M20 washers
      • 1 x Blade retaining strap
      • 2 x M8 screws
    Leadtime on this item can be extended. If you require urgently please contact us before purchasing.
  • View Cart
    Add to basket / Details

    Hub Spring Brackets (Pair)

    €349.50 Excl. VAT     (€419.40 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines.
    Set includes:
    • Top and bottom hub brackets
    • 4 x nuts
    • 4 x washers
  • View Cart
    Add to basket / Details

    IC1100 Control Unit Battery

    €17.48 Excl. VAT     (€20.98 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
  • View Cart
    Add to basket / Details

    Locking Clasp & Adjustable Latch Set

    €69.90 Excl. VAT     (€83.88 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines.
    • 2 x adjustable latches
    • 2 x locking clasps
    Used for locking down the nacelle cover. Made from marine grade stainless steel.
  • View Cart
    Add to basket / Details

    M20 Machined Rod Kit

    €151.45 Excl. VAT     (€181.74 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    New blade pivot rod (machined rod) in accordance with Service Bulletin GWSB010.This kit is included with the Hub bushing kit below and should only be bought separately for use with new hub bushings.Do not use this rod if it appears damaged or has previously been torqued. Once torqued mark the rod so that it is clear it has been torqued.The parts included in this kit:
      • 1 x M20 machined rod
      • 4 x M20 nuts
      • 1 x M20 DTI washer
      • 2 x M20 washers
  • View Cart
    Add to basket / Details

    Motor Circuit Breaker (Motor Guard)

    €174.75 Excl. VAT     (€209.70 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
    • Replacement motor circuit breaker (motor guard).
  • View Cart
    Details

    Motor Controller (Soft Starter)

    €570.85 Excl. VAT     (€685.02 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
    • Replacement motor controller (soft starter).
  • View Cart
    Add to basket / Details

    Nacelle Cover Complete

    €617.45 Excl. VAT     (€740.94 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    Complete with nacelle cover with hinges, latches and decal.
  • View Cart
    Add to basket / Details

    Nylon Bushes

    €63.75 Excl. VAT     (€76.50 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • Supplied as set of 8.
    Nylon bushes are used to retain the blade springs on the teeter hub.
  • View Cart
    Add to basket / Details

    REFURBISHED ANEMOMETER

    €116.50 Excl. VAT     (€139.80 Inc. VAT)
    • Refurbished by Ryse Energy. Your old unit must be returned to us within 14 days.
    • Suitable for the G-11 and G133 wind turbines.
    The anemometer will measure the wind speed accurately to ensure the proper operation of the turbine. The service life of the part is approximately 5 years but can fail within that time due to a number of reasons for example ice build up and bird attacks are the two most common reasons for early failure.
    • Supplied with cable.
  • View Cart
    Add to basket / Details

    Roller Bearing Grease

    €26.80 Excl. VAT     (€32.16 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • 400g highest quality roller bearing grease.
    • Should be used in accordance with the turbine service schedule.
  • View Cart
    Select options / Details

    ROTOR HUB COMPLETE

    €15,057.63 – €15,991.96
    • Suitable for the G-11 and G133 wind turbine
    Complete with:
    • Hub Bushing Kit
    • Bump Stop Kit
    • Spring Kit
    • Hub Bracket
    • Spring Bracket
    • Retaining Strap
    • Inclusive of all fixings
    Supplied without hub fork but available as an option.
  • View Cart
    Add to basket / Details

    Signal Cable (23m)

    €318.05 Excl. VAT     (€381.66 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines on 15m and 18m towers.
    This cable is supplied with:
    • Controller gland
    • 10-way connectors
    • Bootlace ferrules
  • View Cart
    Add to basket / Details

    Signal Cable (33m)

    €559.20 Excl. VAT     (€671.04 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbines on 24m and 27m towers.
    This cable is supplied with:
    • Controller gland
    • 10-way connectors
    • Bootlace ferrules
    • Flexible cable support
    • Modified cable support bracket
    The 33m signal cable is ordered as a special with a lead time of up to 4 weeks.
  • View Cart
    Add to basket / Details

    Transformer 230 / 24V

    €291.25 Excl. VAT     (€349.50 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine fitted with a three phase controller.
  • View Cart
    Add to basket / Details

    Vibration Mounts (Set of 4)

    €128.15 Excl. VAT     (€153.78 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    • Vibration mounts isolate the generator from the machine frame in order to reduce vibration and noise. These rubber mounts will perish over time due to the action of atmosphere on the rubber compound, this can result in the rubber hardening and the metal caps coming away from the rubber.
    • Supplied as a set of 4.
  • View Cart
    Add to basket / Details

    Vibration Sensor

    €81.55 Excl. VAT     (€97.86 Inc. VAT)
    • Suitable for the G-11 and Gaia-Wind G133 wind turbine.
    Sensor is supplied with gland fitted.
Select your currency
GBP Pound sterling
EUR Euro
USD United States (US) dollar
Go to Top